How to Build a Subwoofer Box: Materials, Cut List and Port

WooferGuy is reader-supported. When you buy through an Amazon link on this page we may earn a commission, at no extra cost to you. It never decides what we recommend. How this works.

A custom box is the best way to get the exact volume and tuning your subwoofer wants, in a shape that fits your trunk. It’s also a satisfying weekend project if you have basic tools. The process is simple: design the box to the sub’s specs, cut accurate panels, glue and screw them together airtight, then finish it. This guide walks through each step with a worked cut list.

The short version

  • Design first: get the sub’s recommended volume (and tuning, if ported), then use our box designer.
  • Material: 3/4-inch MDF is the standard; use a double front baffle for big subs.
  • Assemble with wood glue and screws, and seal every joint.
  • Ported? A slot port built from MDF is the easiest to make.
  • Test for leaks before you carpet it.

Tools and materials

ItemNotes
3/4″ MDFStandard for car boxes; stiff, dense, easy to cut
Wood glueA water-resistant glue like Titebond II
Screws1-5/8″ coarse-thread screws; pre-drill to avoid splitting MDF
Silicone or extra glueTo seal inside seams
Terminal cupSpring or binding-post terminals
Polyfill (sealed boxes)Such as Poly-Fil; loosely fill to make a sealed box act slightly larger
Carpet and spray adhesiveSpeaker-box carpet like Siless underfelt carpet
ToolsTable or circular saw with a guide, jigsaw or router with circle jig, drill, clamps, tape measure, square

Step 1: design the box

  1. Find your sub’s recommended sealed volume, or ported volume and tuning, on its spec sheet.
  2. Measure the space in your trunk, including the height under the parcel shelf and the depth at the floor.
  3. Use our box designer to turn net volume into external dimensions and a cut sheet. For ported boxes, the box and port calculator checks tuning and port air speed.
  4. Add the sub’s displacement and any port or bracing volume to get gross internal volume.

Worked cut list

Here’s a simple sealed box, external size 16″ wide × 14″ tall × 13″ deep, from 3/4″ MDF. Front and back are full size; top and bottom fit between them; sides fit inside everything.

PanelQtySize
Front (baffle) and back216″ × 14″
Top and bottom216″ × 11-1/2″
Sides212-1/2″ × 11-1/2″

Internal size is 14-1/2″ × 12-1/2″ × 11-1/2″, about 1.21 cu ft gross. Subtract the sub’s displacement and any bracing to get net volume; that suits a 10-inch sub or a 12 designed for a small sealed box. Check against your sub’s spec before cutting.

Step 2: cut the panels

  • Cut accurately and square; a 1/16″ error on every panel adds up to gaps.
  • Cut the sub hole in the baffle with a jigsaw or, for a cleaner edge, a router on a circle jig. Use the cutout diameter from the sub’s spec sheet.
  • For subs over about 500 W RMS, glue a second layer of MDF to the baffle for stiffness, cutting both layers to the same hole.

Step 3: add a port (ported boxes only)

A slot port is a channel formed by one extra MDF panel running parallel to a side wall. The port’s area and length set the tuning frequency, and the port panel itself takes up volume, so include both in your design. Keep port air speed reasonable to avoid chuffing; the port calculator shows it. Round or chamfer the port opening’s edges to reduce noise.

Step 4: assemble and seal

  1. Dry-fit the panels first.
  2. Run a bead of glue on each edge, clamp, pre-drill and screw every 4–6 inches.
  3. Leave one panel (usually the back or top) off until the end so you can seal the inside seams with glue or silicone.
  4. Add a brace between the largest opposing panels for boxes over about 1.5 cu ft.
  5. Drill and fit the terminal cup, seal it, and run wire to the sub.
  6. Close the box, let the glue cure, then check for leaks by pressing gently on the cone: it should return slowly in a sealed box.

Step 5: finish and fit

  • Wrap the box in carpet with spray adhesive, trimming around the hole and terminal.
  • Add polyfill to a sealed box if your design calls for it.
  • Mount the sub with its gasket and screws, wire it to the right load (see our DVC wiring guide), and strap the box down in the car.

FAQs

Is MDF better than plywood?

For car boxes, MDF is the usual choice because it’s dense and easy to cut accurately. Good birch plywood is lighter and stronger but costs more.

Do I need to brace a small box?

A small, single-sub box in 3/4″ MDF usually doesn’t need bracing. Larger boxes benefit from it.

Sealed or ported?

Our sealed vs ported guide helps you choose by music and space.

Would a prefab box be easier?

Yes. If a ready-made box matches your sub, see our prefab box picks.

Sources

Written by Ryan Smith

Ryan writes WooferGuy for people who want better bass at home and in the car without wading through jargon. Recommendations are based on manufacturer specs, independent measurements where they exist, published reviews, long-term owner feedback and practical setup experience. How we research · Updated November 2026.

Scroll to Top